收藏本站
MAX16824 Evaluation Kit
7) Connect the logic function generator output to each
of the PWM pads (PWM1, PWM2, and PWM3).
8) Connect one LED load anode to each LED output
pad (LED1+, LED2+, or LED3+).
9) Connect each LED load cathode to the correspond-
ing LED input pad (LED1-, LED2-, or LED3-).
10) Enable the power-supply output.
11) Enable the logic function generator signal output.
12) Verify that the attached LEDs are illuminated.
Output Current Setting
The current for each MAX16824 EV kit LED channel
(I LED1 , I LED2 , and I LED3 ) is configured to 100mA by
three sense resistors (R1, R2, and R3, respectively).
See the equation below to select a different LED cur-
rent and a new resistor value. If designing for a higher
LED current, verify that the desired current setting does
not exceed the power rating of the corresponding resis-
tor (R1, R2, or R3) or the LED load. Do not set the LED
current above 150mA. Use the following equation to
calculate the value of the new resistor:
Detailed Description of Hardware
The MAX16824 EV kit demonstrates a high-voltage,
3-channel, linear high-brightness LED driver using the
R _ =
200mV
I LED _
MAX16824 IC in a 16-pin TSSOP surface-mount pack-
age. This EV kit is configured to supply an LED current
of 100mA per channel. The MAX16824 IC controls the
LED current by maintaining a 200mV drop across each
external sense resistor (R1, R2, and R3). The EV kit
operates from a 0.5A, 6.5V to 28V rated power supply.
The three independent PWM inputs (PWM1, PWM2,
and PWM3) control dimming for each channel. Each
PWM input functions as an active-high enable for the
corresponding LED channel.
The MAX16824 features an exposed paddle that uses
the top-layer and bottom-layer PCB copper as a
heatsink. The exposed paddle connects to GND.
LED Load Configuration
The MAX16824 EV kit can drive three separate LED
loads. Each LED load can consist of multiple LEDs con-
nected in series. The LED load’s forward voltage can
be up to 26.3V. The EV kit drives LEDs rated for at least
100mA. Proper heat sinking of the LEDs is important for
optimum LED performance and durability.
where I LED_ is the desired LED current and R_ is the
resistor value required to set the desired current of the
LED channel.
High Input Voltage
and Thermal Protection
The MAX16824 IC operates in linear mode. As a result,
the IC can dissipate significant power if operated using a
high input voltage and a small V FLED . High-power dissi-
pation may cause the IC to go into thermal shutdown.
Refer to the Thermal Protection section in the MAX16824/
MAX16825 IC data sheet for more information.
LED Dimming
The MAX16824 EV kit features three independent PWM
pads used for controlling LED brightness for each
channel. Each channel can have a different dimming
signal pattern. Use a digital PWM signal with a 5V logic
level and a switching frequency between 100Hz and
5kHz. Frequencies lower than 100Hz can introduce
flickering in the light output. Vary the duty cycle of the
signal to adjust the LED brightness. LED brightness
increases as the duty cycle increases and vice versa.
When the PWM signal’s duty cycle is 100%, the LEDs
are continuously on. At 0% duty cycle, the outputs are
disabled.
2
_______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX16825EVKIT+ KIT EVAL FOR MAX16825
MAX16828EVKIT+ EVALUATION KIT FOR MAX16828
MAX16831EVKIT+ KIT EVAL FOR MAX16831
MAX16832CEVKIT+ KIT EVAL FOR MAX16832C LED DVR
MAX16834EVKIT+ EVAL KIT FOR MAX16834
MAX16836EVKIT+ KIT EVAL FOR MAZ16832 LED DRIVER
MAX16839EVKIT+ KIT EVAL FOR MAX16839
MAX16840EVKIT+ KIT EVAL FOR MAX16840 LED DVR
相关代理商/技术参数
MAX16825AUE+ 功能描述:LED照明驱动器 3Ch Linear HB RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16825AUE+T 功能描述:LED照明驱动器 3Ch Linear HB RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16825EUE+ 制造商:Maxim Integrated Products 功能描述:LED DRVR 6SEGMENT 9V/12V/15V/18V/24V 16TSSOP EP - Rail/Tube 制造商:Maxim Integrated Products 功能描述:Hi Volt 3Ch LED Driver MAX16825EUE+
MAX16825EUE+T 制造商:Maxim Integrated Products 功能描述:LED DRVR 6SEGMENT 9V/12V/15V/18V/24V 16TSSOP EP - Tape and Reel
MAX16825EVKIT+ 功能描述:LED 照明开发工具 MAX16825 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
MAX16826AGJ/VY+ 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Rail/Tube
MAX16826AGJ/VY+T 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Tape and Reel
MAX16826ATJ/V+ 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE, FOUR-STRING HB LED DRIVER WITH OUTPUT-VOLTAGE - Rail/Tube